AMERICAN MADE OFF-ROAD INNOVATIONS

MAKING OFF-ROAD GREAT SINCE '98

The Best Ram TRX Upgrades: 2027 SRT TRX and 2021-2024 Leveling Kits, Billet Arms & Protection

Foutz Motorsports · Ram TRX Tech Guide
The Best Ram TRX Upgrades — 2027 SRT TRX and 2021–2024, From Leveling Kits to Billet Arms

Ram brought the TRX back for 2027 with the SRT badge and a supercharged Hellcat V8. We have been building parts for the first one since 2021, and the new truck gets its own catalog rather than a retitled old one. Leveling collars, rear lift plates, billet and fabricated arms, bump stops, skid plates and bed storage — designed, machined and welded in house in Mesa, Arizona.

The Short Answer

The best 2027 Ram TRX upgrades, in the order most owners actually buy them, are a 1.5" front leveling kit to take out the factory rake — on its own that brings the front up about level, so most trucks do not need rear plates with it — then a billet upper control arm kit and billet tie rod kit to get the rubber and the factory ball joint out of the front end, a front limit strap and bump stop kit plus a rear hydraulic bump stop kit to control both ends of the travel, and an underbody skid plate kit with a rear differential skid plate to protect what gets hit first. From there the program continues into fabricated 4130 upper and lower control arms, billet aluminum rear trailing arms on 1" FK uniballs, an adjustable fabricated rear suspension kit with the panhard bar included, adjustable Johnny Joint and heim panhard bars, rear shock skids and mud flap shock guards, Geiser spring packages, an Alcon front big brake kit and a full bed organizer system. The one thing to know before you order: the suspension itself is common across TRX years, front and rear. The control arms, rear links, tie rods, panhard bars, bump stop and limit strap kits, skid plates and bed gear are the same parts whichever TRX you are working on. What changes is how much front lift you can run. Both trucks get front leveling collars in 1.5", 2" and 2.5". On the 2027 truck, anything over 1.5" needs the ride height sensor location corrected, so the 2027 2" and 2.5" kits include adjustable ride height sensor connector rods; the 2021–2024 truck does not need them. Ram did not build a TRX for 2025 or 2026, so parts are listed as separate 2027 and 2021–2024 pages to keep the year unambiguous — buy from the page that matches your truck.

⚠ Where the Factory TRX Runs Out

Both generations of TRX leave the factory as serious equipment. The 2027 SRT TRX carries a supercharged 6.2-liter HEMI Hellcat V8 making 777 horsepower and 680 lb-ft, second-generation Bilstein Black Hawk e2 adaptive shocks with remote reservoirs, a five-link coil-sprung rear on a Dana 60 axle, 35-inch tires and 11.8 inches of ground clearance. None of that is marketing. But a factory suspension is engineered to a warranty, a ride-quality target and a price, and the places it gives up first are the same on both trucks.

The front sits nose-down from the factory, so the truck looks wrong and a 35 sits closer to the fender than it needs to. The upper control arm runs on rubber bushings and a ball joint, so caster and camber are whatever Ram set them to and the arm loads up only after the rubber deflects. The tie rod is the steering component people bend first. The rear arms locate the axle through rubber, which is what makes the back end feel like it is arguing with the front under power. At full droop the front shock is what stops the suspension — it takes the entire top-out load through its own top mount. And past the shock's internal limits at the other end of the stroke, there is nothing between the suspension and the bump stop but hope.

Foutz Motorsports has been a fabrication shop since 1998, and a desert race shop for most of that time. The parts on this page are not catalog items we had made — they are CNC machined, MIG welded and powder coated in our own building in Mesa, Arizona, and most of the designs got found out on our own race trucks before they reached a customer's driveway.

This guide covers the whole TRX program, both generations, sorted by what each part actually does. If you want to skip straight to the catalog, the two collections are 2027+ Ram TRX upgrades and 2021–2024 Ram TRX parts. If you are not sure which truck you have parts for, read the next section first — it is the single most common ordering mistake on this platform right now.

Foutz Motorsports billet aluminum upper control arms installed on a 2027 Ram 1500 SRT TRX front suspension
Billet aluminum upper control arms on the 2027 Ram 1500 SRT TRX — 1.25" FK uniballs at the spindle, 7/8" FK rod ends at the frame, and wheel position sensor mount plates so the adaptive shocks keep reading the suspension.

2021–2024 or 2027? What Actually Changes Between Them

Start with the good news, because it is the opposite of what most people assume about a truck that went away and came back: the suspension parts are common across TRX years. The billet and fabricated control arms, the tie rods, the rear trailing arms and links, the panhard bars, the bump stop and limit strap kits, the skid plates and the bed gear all do the same job on the same mounting points. If you already know this program from a 2021–2024 truck, it carries over to the 2027.

What we do not do is put them all on one listing. Ram did not build a TRX for 2025 or 2026, so a "2021+" fitment line on a TRX part reads as a range covering years the truck did not exist in, and that is how people end up ordering against the wrong truck. Each part gets its own page with its own year list instead. That is a merchandising decision, not a fitment restriction — if a part appears on both collection pages, it fits both trucks.

There is one real exception, and it is the reason to read this section rather than skim it: front lift above 1.5".

Part 2027+ Ram TRX 2021–2024 Ram TRX What to know
Front leveling collar, 1.5" Yes Yes Listed separately so the year is unambiguous
Front leveling collar, 2" and 2.5" Yes Yes The one real difference — the 2027 kits include ride height sensor connector rods; see below
Rear spring spacer lift plates Yes Yes Same plates, same 1.75" stacked ceiling
Billet upper control arms Yes Yes Same arms
Fabricated upper arm kit Yes Yes Same arms
Fabricated lower control arms Yes Yes Same arms
Billet tie rod kit Yes Yes Same kit
Billet half tie rod kit Yes Yes One listing covering every TRX year
Sway bar links for stock bar + fabricated A-arms Yes Yes Same links
Billet top hat Yes Yes Same part
Front limit strap & bump stop kit Yes Yes Upper mount welds to the frame on both
Front bump stop mount kit Yes Yes Welds to the frame
Fabricated front bypass shock mount kit Yes Yes Welds to the frame
Rear bump stop kit Yes Yes Factory spring bucket install on both
Billet rear suspension upper and lower arms Yes Yes Same arms — as a set or individually
Adjustable fabricated rear suspension kit Yes Yes Same kit, panhard bar included
Adjustable panhard bars, Johnny Joint and heim Yes Yes Same bars
Underbody, differential and rear shock skid plates Yes Yes Same protection
Rear shock guard mud flap kit Yes Yes Same kit
Geiser front and rear spring kit Yes Yes One listing, on both collection pages
Alcon front big brake kit Yes Yes 2021+ TRX per the manufacturer
Bolt-on front bumper (2021–2023) No Yes Body part, not suspension — does not fit the 2027
Bed organizers, tire carriers, seat back panels Yes Yes Bed and cargo gear crosses both

Front lift on the 2027 — and the ride height sensor

The 2027 TRX reads its own suspension position electronically. Past about 1.5" of added front height, the ride height sensor is no longer sitting where it was designed to sit, so a taller front kit has to bring the sensor with it — that means adjustable connector rods in the kit, not just a taller collar.

What that means for you: the 2027 2" and 2.5" front leveling kits include adjustable ride height sensor connector rods, set from a 1:1 sheet in the box — 129 mm for the 2" and 126 mm for the 2.5" as a starting point. The 1.5" kit does not need them. If you already have collars, the ride height sensor connector rods are sold as a pair.

The rule of thumb everywhere else: if you have the new truck, buy from the 2027 page. The parts are the same; the year list is there so you order against your own truck. When in doubt, send us the truck and the year and we will tell you which listing you want rather than let you guess.

Leveling Collars and Rear Lift Plates — Stance, Done Properly

More TRX owners buy this than anything else we make, and it has been that way since 2021. The truck leaves the factory with a pronounced nose-down rake. Taking that out is the cheapest change that makes the truck look like what it is, and it is the one upgrade almost everybody does first. The part that matters is how the height gets added.

Under the spring, not on top of the shock

Our front leveling kit is an under-spring preload collar. It mounts to the shock body beneath the lower spring perch and adds preload to the factory coil. The factory spring stays. The factory shock stays, in its factory position. Nothing about the shock's mounting geometry changes.

The other way to do it — the way a top-mount spacer does it — is to put a block above the shock assembly. That does raise the truck, and it does it by pushing the whole shock assembly downward. The suspension then droops farther than it was ever designed to, and the ball joints and CV joints run at angles they were not built for. That is a bind you feel as wear, and eventually as a failed part. It is why we engineered a proper under-spring collar instead of selling a block, and it is the single most useful thing to understand before you buy any TRX lift.

How much lift each truck can take

This is where the two generations differ — not in the heights, which are the same, but in what the 2027 needs above 1.5". It is the fitment question we answer most often.

2021–2024 TRX: 1.5", 2" or 2.5" front. Three separate kits. All three retain the factory shocks and springs, and none of them require changing the factory ride height sensor rod.

2027 TRX: 1.5", 2" or 2.5" front. The 1.5" brings the front up about level on its own. Going higher means bringing the ride height sensor along with the lift, so the 2" and 2.5" kits include adjustable ride height sensor connector rods.

Measure the Truck Before You Order a Height

The TRX has had up to six different factory spring part numbers depending on how the truck was optioned. Two trucks of the same year do not always sit the same. Measure the front and the rear ride height before you choose a collar height — that measurement, not the model year, is what tells you whether 1.5" gets you level or whether you need more.

And plan on an alignment afterward. Any change in front ride height changes camber and toe, and skipping the alignment is how a new set of 35s gets chewed up on the inside edge.

Rear spring spacer plates — and when you actually need them

Most trucks do not need rear plates alongside a front collar. The 1.5" front collar brings the nose up about level on its own, and adding rear height on top of that just puts the rake back in the other direction. The rear spring spacer kit is for the truck that sits low at the back — the one carrying weight, running a bed rack and a spare, or loaded for a trip — where you need to get the rear back up to level. The plates sit directly above the stock spring in the factory spring bucket, so what you get is an even body lift plus added spring preload — the spring rate itself is unchanged. CNC machined from 6061-T6 aluminum, supplied with longer mounting hardware.

Three numbers decide the order, and getting them wrong costs a spring rather than just ride height:

3/4" is the stock application and works with the factory setup as it sits. Any plate thickness over 3/4" requires the FMI rear bump stop kit to work correctly — the 1" plate is the one that triggers that. 1.75" is the maximum recommended stacked height, and you must not stack two 1" plates: that puts the rear into spring bind.

One more thing people find out afterward. Changing rear ride height moves the axle sideways, because the panhard bar swings through an arc as the suspension moves. An adjustable panhard bar is what re-centers the axle under the truck. If you are lifting the rear, budget for it in the same order — the spring bucket is apart anyway.

Stance for the 2027 Ram TRX

2027+ Ram 1500 TRX. Factory coil springs and factory shocks stay on the truck.

Raw billet Foutz Motorsports 1.5 inch leveling collar installed on the front shock body of a 2027 Ram TRX
2027 TRX 1.5" Front Leveling Kit
Enough to bring the front up about level on its own, with no change to the ride height sensor. Under-spring preload collar, factory springs and shocks retained, raw billet or black anodized.
Shop the 2027 1.5" Kit →
Foutz Motorsports black anodized 2 inch front leveling collars with adjustable ride height sensor connector rods for the 2027 Ram TRX
2027 TRX 2" Front Leveling Kit
A clearly lifted stance. Includes the adjustable ride height sensor connector rods the 2027 needs above 1.5". Factory coils and shocks retained, raw billet or black anodized.
Shop the 2027 2" Kit →
Foutz Motorsports black anodized 2.5 inch front leveling collars with adjustable ride height sensor connector rods for the 2027 Ram TRX
2027 TRX 2.5" Front Leveling Kit
The tallest 2027 front stance we offer. Includes the adjustable ride height sensor connector rods. Best on a truck carrying weight up front.
Shop the 2027 2.5" Kit →
Foutz Motorsports billet rear spring spacer plate stacked on a Ram TRX rear bump stop, held in hand
2027 TRX Rear Spring Spacer Lift Kit
1" to 1.75" of rear height in 6061-T6 plates above the stock spring. Over 3/4" requires the rear bump stop kit. Never stack two 1" plates.
Shop the 2027 Rear Plates →
Foutz Motorsports adjustable Johnny Joint panhard bar for the 2027 Ram TRX rear suspension
2027 TRX Adjustable Panhard Bar
What re-centers the rear axle after you change ride height. Johnny Joint or heim versions — both ship fully welded and bolt straight on.
Shop the 2027 Panhard Bar →

Stance for the 2021–2024 Ram TRX

2021, 2022, 2023 and 2024 Ram 1500 TRX. Three front heights, no change to the factory ride height sensor rod.

Foutz Motorsports 2021-2024 Ram TRX front leveling collar kit shown in three lift heights
2021–2024 TRX 1.5" Front Leveling Kit
The mildest of the three. Enough to take the nose-down look out of most trucks without changing much else.
Shop the 1.5" Kit →
Black anodized Foutz Motorsports 2 inch under-spring leveling collar for the 2021-2024 Ram TRX
2021–2024 TRX 2" Front Leveling Kit
The middle height, and the one most 2021–2024 owners land on after they measure. Factory springs and shocks retained.
Shop the 2" Kit →
Black anodized Foutz Motorsports 2.5 inch under-spring leveling collar kit for the 2021-2024 Ram TRX
2021–2024 TRX 2.5" Front Leveling Kit
The tallest collar we build for any Ram platform. Measure first — this is more height than a lot of trucks need.
Shop the 2.5" Kit →
Foutz Motorsports 6061-T6 billet rear spring spacer lift plates for the 2021-2024 Ram TRX
2021–2024 TRX Rear Spring Spacer Lift Kit
Same rules as the 2027 version — 1.75" stacked maximum, plates over 3/4" need the bump stop kit, and never two 1" plates.
Shop the Rear Plates →
Foutz Motorsports adjustable Johnny Joint panhard bar kit for the 2021-2024 Ram TRX rear axle
2021–2024 TRX Adjustable Panhard Bar
Johnny Joint or heim joint. Recenters the axle after a rear lift, and ships fully built — no welding on your end.
Shop the Panhard Bar →
Geiser Off-Road front and rear coil spring kit for the Ram TRX
Geiser TRX Front & Rear Spring Kit
When you want a different rate, not just a different height. Approximately 3" front and 1.5" rear, with rising-rate front and rear coils. Call for availability.
Shop the Geiser Springs →

The Order Most TRX Owners Actually Place

If we look at what leaves the shop, the most common first TRX order is not a leveling kit on its own. It is a front leveling collar together with a billet upper control arm kit and a billet tie rod kit — one visit, one alignment, one labor bill. Rear plates are usually not part of that order, because the front collar on its own gets the truck close to level.

There is a reason those go together. Adding front ride height changes the front geometry, and the billet upper arm is what lets you put caster and camber back where they belong through its rod ends at the frame. The steering is already apart, so the tie rods go in at the same time. You end up with a truck that sits right, aligns right, and has no rubber left in the front upper arms — instead of paying for the same teardown three times.

Six Things That Separate a Real TRX Upgrade From a Spacer

Every part in this program is built to the same set of rules. They are worth stating plainly, because they are the difference between a part that survives a season in the desert and a part that photographs well.

1. The Joint Is the Part

Front billet upper arms run 1.25" FK uniballs at the spindle and 7/8" FK rod ends at the frame. Billet rear arms run 1" FK uniballs. Tie rods use 7/8" FK rod ends at the spindle and 3/4" at the rack. Not pressed-in bushings, not hardware-store shoulder bolts. When a joint eventually wears, you replace the joint — not the arm.

2. Stainless Where It Matters

Every pivot runs 17-4 stainless steel spacers, custom machined for the stock mount locations. The spacer is the part that quietly wears and lets everything else start moving, so it gets the corrosion-resistant material rather than the cheap one.

3. It Bolts Into the Stock Locations

Billet upper arms bolt to the factory spindle — no spindle swap, no cutting. Billet rear arms drop into the stock frame and axle mounts with no frame or axle modification. The two parts that do need welding (the front bump stop mount kit and the fabricated bypass shock mount kit) say so on the listing, and so does the front limit strap kit's upper mount.

4. The Electronics Keep Working

Both TRX generations read suspension position electronically. Our front billet upper arm kits include left and right wheel position sensor mount plates, and the billet rear upper arms carry an aluminum ball post for the rear wheel position sensor. A lower arm never carries one. It is also why the 2027 2" and 2.5" front leveling kits include ride height sensor connector rods rather than a taller collar alone that upsets the sensor.

5. Both Ends of the Travel Get Controlled

Most catalogs sell you height and stop there. A limit strap catches top-out before the shock has to, and a 2.5" bump stop with 2.5" of travel catches the bottom — FOX, King, ADS or Carbon on the front kits, FOX or ADS on the rear. Height without travel control is half a suspension.

6. Made Where It Is Designed

CNC machined, MIG welded, powder coated and anodized in house in Mesa, Arizona, by the same shop that builds and races its own desert trucks. Finishes are raw billet, black anodized, blue anodized and Fox Orange — raw is a deliberate choice a lot of customers make for the machined-aluminum look, not a downgrade.

Get the Rubber and the Ball Joint Out of the Front End

The factory upper control arm runs on rubber bushings and a ball joint. Both are compromises made for ride quality on pavement, and both are why the front end feels like it moves around underneath you when the surface gets rough. Replacing the arm with uniballs and rod ends does two things at once: the arm loads up immediately instead of after the bushing deflects, and caster and camber become adjustable — which is exactly what you need once you have added ride height.

Billet or fabricated — which upper arm

Both replace the factory arm, both put a uniball at the spindle, and both are adjustable at the frame. The difference is how they are made and how they look. Billet is CNC machined from solid aluminum, raw or anodized — choose it if the finish under the truck matters to you. Fabricated is 4130 chromoly tube and plate, MIG welded in fixtures.

The steering is where a failure is not just an inconvenience

The factory tie rod is the weak link people find first, usually at the moment they least want to. The billet tie rod kit replaces both with 6061-T6 aluminum on FK rod ends, with urethane rack boots included to keep water and dirt out of the steering rack — the part most tie rod upgrades leave off, and the one that decides how long the rack lasts. The half tie rod kit is the version that keeps the factory inner tie rod — a simpler install, a serviceable outer link, and slim enough to clear any front shock. It fits every TRX year from one listing.

Front Suspension & Steering — 2027 Ram TRX

2027+ Ram 1500 TRX. Stock length, factory spindle, no track width change.

Foutz Motorsports billet aluminum upper control arm kit installed on a 2027 Ram 1500 SRT TRX
2027 TRX Billet Upper Control Arm Kit
1.25" FK uniballs at the spindle, 7/8" FK rod ends at the frame, 17-4 stainless spacers, wheel position sensor mount plates included. Raw or anodized.
Shop the Billet Upper Arms →
Pair of Foutz Motorsports Ram TRX fabricated 4130 chromoly upper control arms with rod ends
2027 TRX Fabricated Upper Arm Kit
The 4130 chromoly tube-and-plate version of the same job, MIG welded in fixtures in house.
Shop the Fabricated Uppers →
Black fabricated 4130 chromoly lower control arm for the 2027 Ram TRX front suspension
2027 TRX Fabricated Lower Control Arms
Stock length, built to survive the impacts that bend a factory arm — and they carry their own integrated bump pad.
Shop the Fabricated Lowers →
Foutz Motorsports Ram TRX billet tie rod kit with both tie rods, urethane rack boots, clamps and hardware
2027 TRX Billet Tie Rod Kit
6061-T6 billet on 7/8" FK rod ends at the spindle and 3/4" at the rack, with urethane rack boots and grade 8 hardware.
Shop the Tie Rod Kit →
Foutz Motorsports Ram TRX sway bar links for the stock sway bar with fabricated lower A-arms
2027 TRX Sway Bar Links
For keeping the stock sway bar once fabricated A-arms are on the truck. Same links across TRX years, listed per truck.
Shop the Sway Bar Links →
Pair of black anodized Foutz Motorsports billet top hats for the Ram TRX front shock
2027 TRX Billet Top Hat — Stock Height
Billet replacement for the factory top hat at stock ride height, for the factory shock.
Shop the Billet Top Hat →

Front Suspension & Steering — 2021–2024 Ram TRX

2021, 2022, 2023 and 2024 Ram 1500 TRX. Stock length, factory spindle.

Foutz Motorsports billet aluminum upper control arm kit for the 2021-2024 Ram TRX
2021–2024 TRX Billet Upper Control Arm Kit
The original TRX billet upper arm, stock length, adjustable at the frame so you can set caster and camber after a lift.
Shop the Billet Upper Arms →
Pair of Foutz Motorsports Ram TRX fabricated upper control arms on the shop floor with rod ends fitted
2021–2024 TRX Fabricated Upper Arm Kit
4130 chromoly, MIG welded in house. The fabricated alternative to the billet arm.
Shop the Fabricated Uppers →
Foutz Motorsports fabricated stock-length lower control arm for the 2021-2024 Ram TRX front suspension
2021–2024 TRX Fabricated Lower Control Arms
Stock length, built to survive impacts that bend the factory arm.
Shop the Fabricated Lowers →
Foutz Motorsports Ram TRX billet aluminum tie rod kit
2021–2024 TRX Billet Tie Rod Kit
Billet aluminum tie rods on FK rod ends for the 2021–2024 steering rack.
Shop the Tie Rod Kit →
Foutz Motorsports billet half tie rod kit for the Ram TRX, laid out with hardware
Billet Half Tie Rod Kit — Every TRX Year
One listing covering 2021–2024 and 2027+ TRX — the version that keeps the factory inner tie rod.
Shop the Half Tie Rod Kit →
Two black anodized Foutz Motorsports billet top hats for the Ram TRX front shock at stock height
2021–2024 TRX Billet Top Hat — Stock Height
Billet top hat for the factory shock at stock ride height.
Shop the Billet Top Hat →

Both Ends of the Stroke — Limit Straps and Bump Stops

This is the section people skip, and it is the one that saves parts. On a stock TRX the front shock is what stops the suspension at full droop — it takes the entire top-out load through its own top mount. That is fine on a driveway and expensive in the desert, and it is the single most common way a front shock mount gets killed.

The front limit strap and bump stop kit handles both ends at once: a 12" strap built from four layers of military-grade webbing with black-plated steel mounting tabs to catch top-out before the shock does, and a bracket with an integrated bump stop pad for the bottom of the stroke. The brackets clamp around the front of the stock lower control arm, are MIG welded in house and finished in hammer black powder coat. If you are running aftermarket springs, this is not optional — springs change where the suspension sits and how far it extends, which makes top-out control more important, not less.

One mount bolts, one mount welds — read this before ordering

The front limit strap kit for the stock lower arm installs two ways at once, and the second half is the part people miss. The lower mount bolts on, to the factory cast aluminum lower control arm, using the included hardware — nothing is cut or drilled on the arm. The upper mount must be welded to the frame. There is no bolt-on option for the frame end. Budget for a qualified welder alongside the kit rather than discovering it once the parts arrive.

Already running our fabricated lower control arms? Those carry their own integrated bump pad, so the part you want is the front bump stop mount kit instead. That one also welds to the frame.

The rear runs out first

The rear of a TRX runs out of travel before the front does, and when it does the hit goes straight into the frame. The rear bump stop kit installs into the factory rear spring buckets with minimal modification and takes a 2.5" bump stop with 2.5" of travel. Order it with FOX or ADS hydraulic bump stops included, or choose NONE and get the mount sections and hardware only — the right call if your shock package already came with bump stops. Remember that this kit is also required if you run rear spring spacer plates thicker than 3/4".

Limit Straps & Bump Stops — 2027 Ram TRX

2.5" bump stops with 2.5" of travel — FOX, King, ADS or Carbon on the front kits, FOX or ADS on the rear.

Foutz Motorsports limit strap and bump stop kit installed on a 2027 Ram TRX front suspension
2027 TRX Front Limit Strap & Bump Stop Kit
For the factory cast aluminum lower arm. 12" four-layer straps, integrated bump pad. Lower mount bolts on, upper mount welds to the frame.
Shop the Limit Strap Kit →
CAD render of the Ram TRX front suspension with the weld-on bump stop mount kit for fabricated lower arms
2027 TRX Front Bump Stop Mount Kit
The version for trucks already on fabricated lower arms. Welds to the frame — qualified welder or fabricator.
Shop the Bump Stop Mounts →
Pair of Foutz Motorsports Ram TRX rear bump stop mount cans with hydraulic bump stops fitted and install hardware
2027 TRX Rear Bump Stop Kit
Installs in the factory rear spring buckets. 2.5" bump stop with 2.5" of travel, in FOX or ADS — or mounts only.
Shop the Rear Bump Stops →
CAD render of the Foutz Motorsports Ram TRX fabricated front bypass shock mount tower
2027 TRX Fabricated Front Bypass Shock Mount Kit
The top of the front program — mounting for a front bypass shock. Welds to the frame.
Shop the Bypass Mount Kit →

Limit Straps & Bump Stops — 2021–2024 Ram TRX

Same architecture, built for the first-generation truck.

Foutz Motorsports front limit strap and bump stop kit for the 2021-2024 Ram TRX stock lower control arm
2021–2024 TRX Front Limit Strap & Bump Stop Kit
For the stock lower arm. Controls top-out and bottom-out on the first-generation truck — and like the 2027 version, its upper mount welds to the frame.
Shop the Limit Strap Kit →
CAD render of the Ram TRX weld-on front bump stop mount kit for use with fabricated lower A-arms
2021–2024 TRX Front Bump Stop Mount Kit
For trucks already running fabricated lower arms. Welds to the frame.
Shop the Bump Stop Mounts →
Foutz Motorsports rear bump stop kit with hydraulic bump stops for the 2021-2024 Ram TRX
2021–2024 TRX Rear Bump Stop Kit
Factory spring bucket install, with optional hydraulic bump stops. Required above 3/4" of rear spacer plate.
Shop the Rear Bump Stops →

The Rear End — Where Wheel Hop Comes From

The TRX shipped with a coil-sprung five-link rear from the start, so there is no leaf-to-link conversion to do here. The work is about control and strength rather than architecture. Every rubber bushing in the factory rear end is a part designed to move, and that compliance is exactly what makes the truck quiet on pavement and vague under power. Wheel hop is the axle winding up against soft bushings and releasing. Take the rubber out and the axle goes where the arm puts it.

There are two ways to do it, and they suit different builds:

Billet aluminum rear arms — stock geometry, better joints

Four CNC machined billet aluminum arms — two uppers, two lowers — on 1" FK uniballs with custom 17-4 stainless spacers sized for the stock mount locations. No frame or axle modification. A urethane wobble stopper at the front mounts keeps the arms from walking side to side, and the upper arms carry an aluminum ball post for the rear wheel position sensor, so the adaptive shocks keep reading rear suspension position. Sold as the full four-arm kit, or as uppers and lowers individually if you are doing the job in stages. The panhard bar is a separate part.

Adjustable fabricated rear kit — when you want to set axle position

The adjustable kit replaces the upper and lower trailing arms and the panhard bar with adjustable 4130 chromoly components: lowers on 1.5" uniballs at the frame and 1.25" rod ends at the axle, uppers on 1" uniballs and 1" rod ends, plus an adjustable fabricated panhard bar. Five pieces in total, with the panhard bar included rather than sold separately. It works with stock shocks and springs — this is a linkage upgrade, not a whole rear suspension replacement — and it installs in a few hours. Choose it when you want to set pinion angle and axle position rather than accept them.

Panhard bars — and what "weld on" means on the spec sheet

The panhard bar, also called a track bar, is what controls side-to-side axle location, and the trailing arms cannot do that job for it. Our adjustable bars come in a Johnny Joint version and a heim joint version. Both ship fully welded and ready to bolt on. If you see a line in the kit contents reading "1" Johnny Joint weld on assembly", that describes a joint type — a fixed joint already welded into the bar at our shop — not a job for you or your installer. One end threads in so the bar adjusts for length; the other end is the welded-in fixed joint. Neither bar requires the customer to weld anything.

Rear Suspension — 2027 Ram TRX

2027+ Ram 1500 TRX, factory rear mount locations, no frame or axle modification.

Raw billet aluminum Foutz Motorsports rear suspension arm installed under a 2027 Ram TRX on a shop lift
2027 TRX Billet Rear Suspension Arm Kit
All four arms — two uppers, two lowers — on 1" FK uniballs with urethane wobble stoppers and an aluminum ball post on the uppers.
Shop the Billet Rear Arm Kit →
Foutz Motorsports fabricated adjustable rear trailing arm installed on a 2027 Ram TRX
2027 TRX Adjustable Rear Suspension Kit
Five pieces in adjustable 4130 chromoly, panhard bar included. Works with stock shocks and springs, installs in a few hours.
Shop the Adjustable Rear Kit →
Raw billet aluminum Ram TRX rear suspension upper arms with the aluminum ball post for the wheel position sensor
2027 TRX Billet Rear Upper Arms
The upper pair on their own — these are the arms that carry the ball post for the rear wheel position sensor.
Shop the Upper Arms →
Ram TRX on a shop lift with raw billet aluminum rear lower suspension arms fitted
2027 TRX Billet Rear Lower Arms
The bottom pair on their own, for a build done in stages. A lower arm never carries a ball post.
Shop the Lower Arms →
Foutz Motorsports adjustable Johnny Joint panhard bar kit for the 2027 Ram TRX
2027 TRX Adjustable Panhard Bar — Johnny Joint
Ships fully welded, bolt-on. Recenters the axle after any change in rear ride height.
Shop the Johnny Joint Bar →
Foutz Motorsports adjustable heim joint panhard bar for the 2027 Ram 1500 TRX rear suspension
2027 TRX Adjustable Panhard Bar — Heim Joint
The heim version of the same bar. Also fully built and bolt-on, no welding required.
Shop the Heim Joint Bar →

Rear Suspension — 2021–2024 Ram TRX

2021, 2022, 2023 and 2024 Ram 1500 TRX.

Foutz Motorsports billet aluminum rear suspension arm kit fitted to a 2021-2024 Ram TRX
2021–2024 TRX Billet Rear Arm Kit
The same four billet arms as the 2027 kit, listed for the first-generation truck.
Shop the Billet Rear Arms →
Foutz Motorsports adjustable fabricated rear suspension kit installed on a 2021-2024 Ram TRX
2021–2024 TRX Adjustable Rear Suspension Kit
Adjustable fabricated trailing arms and panhard bar for the first-generation truck.
Shop the Adjustable Rear Kit →
Foutz Motorsports adjustable heim joint panhard bar kit for the 2021-2024 Ram TRX
2021–2024 TRX Panhard Bar — Heim Joint
Adjustable track bar in the heim joint version. Fully built and bolt-on.
Shop the Heim Joint Bar →

Armor for the Parts That Get Hit First

Two failures end a day out more often than anything else on this truck, and both are cheap to prevent.

The rear differential cover seal

The bottom of the rear diff cover seal is a known weak point on trucks that see real off-road use. A rock does not have to punch through the cover — it only has to catch the lower back plate and work the gasket loose, and then you are watching gear oil run out on the trail. The rear differential skid plate covers exactly that. One caveat: it will not work with aftermarket diff covers unless specified, because those change the shape and bolt pattern the skid has to clear. If you have already fitted one, tell us what it is before ordering.

The bottom of the rear shock

The lower end of the rear shock sits low, outboard and directly in the path of anything the rear tire picks up. One rock caught square on a shock body is a leak, and a leaking rear shock ends the day. The rear shock skid kit shields the bottom of the shock and the rear axle mounts in 3/16" MIG welded steel with a black textured powder coat. The main mount attaches to the shock bolt with longer bolts supplied, and an additional bolt on the back plate stops the skid rotating on a single fastener. It is the same skid across TRX years, listed on both collection pages.

The transmission crossmember, not just the guards

The factory guards cover the transmission, but the crossmember they hang from is the part that bends in heavy rock. Once it does, the transmission mount moves and the damage stops being cosmetic. Our underbody kit is four pieces laser cut from 3/16" aluminum and CNC bent in house: a center front plate over the differential and steering area, a main mid plate over the transmission, a transfer case guard for the rear exposed section of the t-case, and a transmission crossmember support plate that stiffens the crossmember itself and gives the rear skid something to mount to. Sold as a full kit only, because the pieces work as one system.

Protection — 2027 Ram TRX

2027+ Ram 1500 TRX. Laser cut, CNC bent, MIG welded and powder coated in house.

Raw aluminum Foutz Motorsports underbody skid plate installed on a 2027 Ram TRX with the exhaust alongside
2027 TRX Underbody Skid Plate Kit
Four pieces in 3/16" aluminum covering diff, steering, transmission and transfer case — plus the crossmember support plate.
Shop the Skid Plate Kit →
Black rear differential skid plate installed under a 2027 Ram TRX with the rear coil spring in view
2027 TRX Rear Differential Skid Plate
Covers the diff cover seal and the lower back plate. Not compatible with aftermarket diff covers unless specified.
Shop the Diff Skid →
Black powder coated Foutz Motorsports rear shock skid installed on a 2027 Ram TRX beside the rear tire
2027 TRX Rear Shock Skid Kit
3/16" MIG welded steel shielding the bottom of the shock and the axle mounts. The same skid across TRX years.
Shop the Shock Skid →
Foutz Motorsports rear shock guard mud flap frame mount kit for the 2027 Ram TRX
2027 TRX Rear Shock Guard Mud Flap Kit
Frame-mounted flaps that keep rock and debris off the shock bodies. The companion to the shock skid.
Shop the Mud Flap Guards →

Protection — 2021–2024 Ram TRX

2021, 2022, 2023 and 2024 Ram 1500 TRX.

Foutz Motorsports underbody skid plate kit fitted to a 2021-2024 Ram TRX
2021–2024 TRX Underbody Skid Plate Kit
Four-piece kit covering the diff and steering area, transmission and transfer case, plus the crossmember support plate.
Shop the Skid Plate Kit →
2021 Ram TRX rear axle with the Foutz Motorsports rear differential skid plate fitted
2021–2024 TRX Rear Differential Skid Plate
Same job on the first-generation rear axle — protect the cover seal before a rock finds it.
Shop the Diff Skid →
Foutz Motorsports rear shock skid kit installed on a 2021-2024 Ram TRX rear axle
2021–2024 TRX Rear Shock Skid Kit
The cross-generation shock skid, listed for the first-generation truck.
Shop the Shock Skid →
Foutz Motorsports rear shock guard mud flap frame mount kit on a 2021-2024 Ram TRX
2021–2024 TRX Rear Shock Guard Mud Flap Kit
Keeps rock and debris off the rear shock bodies on the first-generation truck.
Shop the Mud Flap Guards →

The Parts We Do Not Make Ourselves

A few things on the TRX are better bought from the people who specialize in them, so we carry those rather than build a version of our own. On these, the manufacturer's stated fitment is the fitment — we do not extend a vendor's year range on our own authority.

Brakes

The Alcon front big brake kit is the one to know about, because it is engineered to fit the OEM 18" wheel rather than forcing a wheel change. Six-piston ductile iron calipers, 376 x 42 mm rotors, heavy duty pad material, high-temperature motorsport seals with a wiper seal on every piston, and compatibility with the stock actuation. Alcon quotes up to an 8% reduction in pad work rate and up to a 7% increase in available brake torque over stock, along with a large gain in available thermal mass. On a 777-horsepower truck on 35s, that matters more than it does on most things.

Springs

Collars and plates change ride height. Springs change the rate, which is a different tool for a different problem. The Geiser TRX spring kit gives approximately 3" of front lift and 1.5" of rear, with front coils at 920 lbs rising to 1000 lbs after the first 2" of travel (stock is 950 lbs), and rear coils at 240 lbs rising to 310 lbs (stock is 225 rising to 295). Call for availability on these. Eibach Pro-Truck lift kits and spring sets are also stocked for the first-generation TRX, carrying Eibach's own stated fitment rather than ours.

Shocks

For a full shock package on the first-generation truck, the Carbon Shock Technologies Stage 2 package pairs a 3.0 front coil-over with a 3.0 rear four-tube bypass, listed by the manufacturer for the 2021–2025 TRX. Everything in our own front and rear program is designed to work alongside a package like that rather than against it.

A Bed That Stays Organized

Gear that is not mounted is gear that is loose in the bed. The Adapt-a-panel system turns the bed side wall into a full grid of mounting points, so fuel cans, axes, shovels, power tanks and hi-lift jacks all have a fixed home. Three panels cover one side of the bed in .135" thick 1018 steel — heavy enough for the things people actually carry — with full coverage even over the cleat area, quick attach to existing hardware locations, and grid inserts that can be added or moved at any time after install. You are not committing to a layout on day one.

On top of that sits the quick-release modular bed organizer system: single and dual tire carriers that lift out on quick-release pins, with cleats that sit nearly flush with the bed ribs so the bed floor stays usable, upright support tubes sold in pairs, and a universal PACKOUT mounting plate for the tool boxes a lot of people are already running. Inside the cab, the seat back panel kits carry recovery gear, or a shovel, hammer and fire extinguisher. All of this crosses both TRX generations.

Bed Storage & Gear — Both Generations

Bed and cargo gear fits the 2027+ TRX and the 2021–2024 TRX. Bed panel kits are listed per generation; the rest is universal.

Adapt-a-panel grid panel installed along the bed side wall of a Ram TRX
2027 TRX Bed Organizer Panel Kit — One Side
Three panels in .135" 1018 steel covering one side of the bed, with six standoffs and stainless hardware.
Shop the 2027 Bed Panels →
Foutz Motorsports Adapt-a-panel bed organizer panel kit fitted in a 2021-2024 Ram TRX bed
2021–2024 TRX Bed Organizer Panel Kit
The same panel system for the first-generation bed.
Shop the Bed Panels →
Foutz Motorsports single tire carrier quick release modular truck bed organizer
Single Tire Carrier Bed Organizer
Quick release on a quick pin, fully adjustable left to right to fit any bed, and the cleats sit nearly flush with the bed ribs when it comes out.
Shop the Single Carrier →
Foutz Motorsports dual tire carrier quick release modular bed organizer loaded in a truck bed
Dual Tire Carrier Bed Organizer
Two spares on the same quick-release system. Fuel jug trays, jack mounts and light mount add-ons are available across the organizer line.
Shop the Dual Carrier →
PACKOUT tool box storage mounting plate fitted to a truck bed side wall
PACKOUT Universal Mounting Plate
Mounts a PACKOUT stack to the bed side wall on any vehicle, TRX included.
Shop the PACKOUT Plate →
Off-road seat back panel kit with recovery gear mounted behind a truck seat
Off-Road Seat Back Panel Kit
Recovery gear, or shovel, hammer and fire extinguisher — mounted behind the seat instead of loose in the cab.
Shop the Seat Back Panels →

What You Are Actually Choosing Between

There are four broad ways to change a TRX's suspension. They are not equally reversible, and they do not all leave you somewhere you can build from.

What you care about Foutz Motorsports Top-mount strut spacer lift General catalog bolt-on parts Full aftermarket coil-over swap
How front lift is added Under-spring preload collar below the lower perch Block above the shock assembly Varies, usually a spacer New spring and shock package
Factory shock position kept Yes No — the assembly moves down Varies No
Ball joint and CV angles Unchanged at droop Extra droop, added bind Often not considered Designed into the kit
Caster and camber after a lift Adjustable at the upper arm rod ends Whatever you end up with Usually fixed Depends on the kit
Adaptive shock sensors Sensor plates and ball post included by design Unchanged Varies Often a problem
Rear arm joints 1" FK uniballs, serviceable, urethane wobble stoppers Factory rubber stays Uniball or poly bushing Uniball
Bottom-out protection 2.5" bump stops front and rear, in the shock brand you already run None Rarely offered Usually included
Top-out protection Limit straps, so the shock does not take the hit None Rarely offered Varies
2027 ride height sensor addressed Yes — connector rods included above 1.5" Rarely mentioned Rarely mentioned Varies
Path to more later Every stage bolts onto the last Dead end Mixed brands, mixed geometry Already at the end
Who engineered it A race shop, on its own desert trucks Contract manufacturer Catalog supplier Varies
Where it is made Mesa, Arizona — in house Varies Varies Varies

The column that matters most over time is the second-to-last one. A spacer lift is a destination. Everything in our program is a step you can build past without throwing the last part away.

What to Buy for How You Actually Drive It

Most TRX owners fall into one of two groups, and they should not buy the same list.

Street, Trail and Weekend Duty
Front leveling collar to take the rake out — usually enough on its own
Billet upper control arms so you can align it properly afterward
Billet tie rod kit, done in the same teardown
Rear spring spacer plates only if you carry weight in the back, with an adjustable panhard bar to recenter the axle
Rear differential skid plate and rear shock skid — cheap insurance
Bed organizer panels and a tire carrier for the gear
All bolt-on, all reversible, all still useful later
Desert, Dunes and High Speed
You are hitting things at speed and the truck knows it
Front limit strap and bump stop kit — both ends of the travel
Rear hydraulic bump stop kit, done at the same time as the front
Fabricated 4130 lower control arms and fabricated upper arms
Billet rear arms, or the adjustable fabricated rear kit with the panhard bar included
Full underbody skid plate kit with the crossmember support
Geiser springs if you carry weight, and the fabricated front bypass shock mount kit at the top end

If you are not sure which list you are on, the honest test is whether the truck ever leaves the ground. If it does, buy the travel-control parts before the cosmetic ones.

The Order We Would Build It In

This is the sequence that costs the least in duplicated labor, because each step opens up the next one.

1

Measure the Truck

Front and rear ride height, before anything is ordered. With up to six factory spring part numbers on the TRX, the measurement — not the model year — tells you which collar height you need.

2

Front Leveling Collar, Upper Arms and Tie Rods Together

One teardown, one alignment, one labor bill. The collar sets the height, the billet upper arms give you the adjustment range to align it afterward, and the tie rods go in while the steering is already apart.

3

Rear Plates and the Panhard Bar — Only If the Back Sits Low

Skip this step unless you are carrying weight in the back. The front collar alone gets most trucks close to level, and adding rear height on top of it just tips the rake the other way. If the back does sit low, choose the plate thickness against the 1.75" ceiling, add the rear bump stop kit if you are going over 3/4", and fit the adjustable panhard bar to bring the axle back to center — the spring bucket is open either way.

4

Get the Alignment Done

Not optional after any ride height change. Camber and toe both move, and a set of 35s will tell you about it on the inside edges within a few thousand miles.

5

Armor Before the Next Trip

Rear differential skid plate, rear shock skid, mud flap shock guards, then the full underbody kit. These are the parts that pay for themselves the first time a rock finds the diff cover seal.

6

Control Both Ends of the Travel

Front limit strap and bump stop kit, and the rear bump stop kit. Do them together — controlling one end and not the other just moves where the truck gets hurt. Remember the front kit's upper mount welds to the frame, so book the welder in advance.

7

Then Go Deeper: Arms, Rear Links, Springs, Shocks

Fabricated lower control arms, billet or adjustable fabricated rear links, a Geiser spring package if you carry weight, and the front bypass shock mount kit when a bypass shock is on the list. Nothing you bought in steps 2 through 6 gets thrown away to get here.

A Fabrication Shop First

Foutz Motorsports has been making off-road great since 1998. We are a fabrication shop before we are a parts brand: the CNC machines, the welding fixtures, the powder coat booth and the anodizing are all in one building in Mesa, Arizona, and the parts on this page were designed by the same people who run them.

The other half of that is the race program. We build and campaign our own desert trucks, which is where most of these designs got found out long before they reached a customer's driveway. A limit strap kit exists because we watched what happens to a front shock mount that has to stop the suspension by itself. A crossmember support plate exists because we bent a crossmember. That is a slower way to develop a catalog, and it is why the fitment notes on these listings are as specific as they are.

Shipping and lead times

Most in-stock items ship within 48 hours to the US and Canada, with next-day shipping available on domestic orders. Built-to-order items typically run 4 to 6 weeks.

Not sure what you need?

Send us the year of your truck, what is already on it, and how you actually drive it. We will tell you what to buy first — and, just as often, what to skip.

Ram TRX Upgrade FAQs

What are the best upgrades for a 2027 Ram TRX?

The best place to start is a 1.5" front leveling kit to take out the factory rake — on its own that brings the front up about level, so you would only add rear spring spacer plates if you are carrying weight in the back and need to get level again. Fit it together with a billet upper control arm kit and a billet tie rod kit so the truck can be aligned properly afterward and the rubber and factory ball joint are out of the front end. After that, the highest-value upgrades are a front limit strap and bump stop kit with a rear hydraulic bump stop kit to control both ends of the travel, and protection — the rear differential skid plate, rear shock skid and the four-piece underbody skid plate kit with the transmission crossmember support. From there the program continues into fabricated 4130 control arms, billet aluminum rear trailing arms on 1" FK uniballs, the adjustable fabricated rear suspension kit, adjustable panhard bars, Geiser spring packages and the Alcon front big brake kit.

Do 2021–2024 Ram TRX parts fit the 2027 TRX?

Yes — the suspension parts are common across TRX years, front and rear. The billet and fabricated control arms, the tie rods and half tie rods, the sway bar links, the billet top hats, the rear trailing arms and links, the adjustable rear suspension kit, the panhard bars, the limit strap and bump stop kits, the skid plates and shock guards, the Geiser springs, the Alcon brakes and all the bed and cargo gear do the same job on both trucks. They are listed as separate 2027 and 2021–2024 pages so the year is never ambiguous, not because the parts differ. The two exceptions are front leveling collars taller than 1.5" — on the 2027 those need ride height sensor connector rods, which the 2027 2" and 2.5" kits include — and the 2021–2023 bolt-on front bumper, which is a body part and does not fit the newer truck. Buy from the page that matches your truck's year.

Why are 2027 TRX parts listed separately if they are the same parts?

Because Ram did not build a TRX for the 2025 or 2026 model years, so a "2021+" fitment line on a TRX part would claim a range covering years the truck did not exist in. Listing each part with the specific years it fits is how we keep that unambiguous. It is a merchandising decision rather than a fitment restriction — if a part appears on both collection pages, it fits both trucks.

How much front lift can you put on a 2027 Ram TRX?

1.5", 2" or 2.5". The 1.5" on its own brings the front up about level. Going higher is not a clearance or bracket question — it is the ride height sensor, which past roughly 1.5" is no longer sitting where it was designed to, so the 2027 2" and 2.5" kits include adjustable ride height sensor connector rods. The 2021–2024 TRX is offered in the same three heights without them.

Can I run more than 1.5" of front lift on a 2027 Ram TRX?

Yes, with the right kit. Going higher on the 2027 means correcting the ride height sensor location, so buy the 2027 2" or 2.5" kit, which includes adjustable ride height sensor connector rods. The 1.5" kit on its own gets most trucks close to level.

What front leveling heights fit the 2021–2024 Ram TRX?

1.5", 2" and 2.5", sold as three separate kits. All three retain the factory shocks and the factory coil springs, and none of them require changing the factory ride height sensor rod.

What is the best leveling kit for a Ram TRX?

The one that adds height under the spring rather than on top of the shock. Our TRX front leveling kit uses an under-spring collar that mounts to the shock body beneath the lower spring perch and adds preload to the factory coil, so the shock stays in its factory position and the suspension geometry is unchanged at droop. A top-mount block raises the truck by pushing the whole shock assembly downward, which lets the suspension droop farther than it was designed to and puts the ball joints and CV joints at angles they were not built for. Both approaches raise the truck; only one of them leaves the front end where the factory put it.

Why is a spacer on top of the shock bad on a TRX?

It moves the entire shock assembly down. The suspension then extends farther than it was intended to, which puts bind on the ball joints and CV joints and causes premature failures. Adding preload under the spring gets you the ride height without moving the shock or changing what the joints see at full droop.

Do the leveling kits require new shocks or springs?

No. The collar adds preload to the factory coil spring and the factory shock stays in its original position. Nothing else has to come off the truck.

Do I need an alignment after installing a leveling kit?

Yes. Any change in front ride height changes camber and toe. Get the truck professionally aligned afterward or you will see uneven front tire wear, usually on the inside edge. This is also the reason a billet upper control arm kit pairs so well with a lift — its rod ends at the frame are what give the shop the adjustment range to put caster and camber back where they belong.

How do I choose which lift height to order?

Measure the front and the rear ride height of your own truck first. The TRX has had up to six different factory spring part numbers depending on options, so two trucks of the same year do not always sit the same. Measure both ends, decide how much rake you actually want to remove, and order to that number rather than to the model year.

How much rear lift do the TRX spring spacer plates give?

Between 1" and 1.75" depending on the plates used, with 1.75" the maximum recommended stacked height. The plates sit directly above the stock spring in the factory spring bucket, so the result is an even body lift plus added preload — the spring rate itself does not change, which is what makes them the right fix for a truck that sits low because it is loaded.

Can I stack two 1" rear spacer plates to get 2"?

No. That exceeds the 1.75" maximum recommended stacked height and puts the rear springs into bind. Stackable combinations with our bump stop kits are 3/4" plus 3/4", or 3/4" plus 1".

When do the rear spacer plates require a bump stop kit?

Any plate thickness over 3/4" requires the Foutz Motorsports rear bump stop kit to work correctly. The 3/4" plate is the stock application and works with the factory setup as it sits; the 1" plate is the one that triggers the requirement.

Do I need an adjustable panhard bar after a rear lift?

Strongly recommended. The panhard bar swings through an arc as the suspension moves, so changing rear ride height pulls the axle off-center underneath the truck. An adjustable panhard bar — also called a track bar — is what brings it back to center. The spring bucket is already apart when the plates go in, so it is the obvious thing to do at the same time.

Do the adjustable panhard bars require welding?

No. Both the Johnny Joint and the heim joint versions ship fully welded and ready to bolt on. A kit-contents line reading "Johnny Joint weld on assembly" describes a joint type — a fixed joint already welded into the bar at our shop — not an install step. One end threads in so the bar adjusts for length, and the other end is that welded-in fixed joint.

Which TRX parts actually require welding?

Three. The front bump stop mount kit and the fabricated front bypass shock mount kit both weld to the frame. The front limit strap and bump stop kit installs two ways at once — its lower mount bolts to the factory cast aluminum lower control arm, but its upper mount must be welded to the frame, and there is no bolt-on option for that end. All three should be installed by a qualified welder or fabricator. Everything else in the program bolts on.

Will the adaptive suspension still work with aftermarket control arms?

Yes, because the kits are built around it. The billet upper control arm kits include left and right wheel position sensor mount plates, and the billet rear upper arms carry an aluminum ball post for the rear wheel position sensor. Those are the parts the shock control module reads.

What is a ball post, and which arm carries it?

The ball post is the small post that carries the wheel position sensor. It is fitted to upper links only — a lower link never carries one. On our billet rear upper arms the ball post is aluminum; on fabricated rear upper links it is a steel post welded in.

Billet or fabricated upper control arms — which should I buy?

Both replace the factory upper arm, both put a uniball at the spindle and both are adjustable at the frame, so the performance decision is close. Billet arms are CNC machined from solid aluminum and available raw or anodized — choose them if the finish under the truck matters to you. Fabricated arms are 4130 chromoly tube and plate, MIG welded in fixtures.

What does a limit strap actually do?

It catches the suspension at full droop so the shock does not have to. On a stock truck the front shock and its top mount absorb every top-out hit, which is the most common way a front shock mount gets damaged. Our straps are 12" long, four layers of military-grade webbing, with black-plated steel mounting tabs. If you run aftermarket springs, top-out control matters more, not less.

Which bump stops do the TRX kits use?

2.5" bump stops with 2.5" of travel at both ends. The front kits are built around FOX, King, ADS or Carbon; the rear kit is offered with FOX or ADS. On the rear kit you can also choose NONE and take the mount sections and hardware only — the right option if your shock package already came with bump stops.

Is the panhard bar included with the rear arm kits?

It depends on the kit. The adjustable fabricated rear suspension kit includes it — five pieces in total, four trailing arms plus the adjustable panhard bar. The billet aluminum rear arm kit does not; it is four arms, and the panhard bar is a separate part.

What does the wobble stopper do, and what is it made of?

The wobble stopper sits at the front mounts and keeps the arm from walking side to side, so the axle stays where you set it. All Foutz Motorsports wobble stoppers are urethane.

Does the rear differential skid plate work with an aftermarket diff cover?

Not unless specified. Aftermarket covers change the shape and the bolt pattern the skid has to clear. If you have already fitted one, contact us with what it is before ordering rather than assuming the skid will fit around it.

Does the Alcon big brake kit fit the stock TRX wheels?

Yes — it is designed to fit the OEM 18" wheel, which is unusual for a big brake kit this size. Six-piston ductile iron calipers on 376 x 42 mm rotors, heavy duty pad material, and compatibility with the stock brake actuation. There is a wheel template on the product page if you are running something other than the factory wheel.

Which TRX parts are made in the USA?

All Foutz-branded TRX components are designed, CNC machined, MIG welded, powder coated and anodized in house in Mesa, Arizona. Third-party items in the collections — Alcon brakes, Geiser and Eibach springs, Carbon shocks — come from their own manufacturers and carry those manufacturers' stated fitment.

How fast do orders ship?

Most in-stock items ship within 48 hours to the US and Canada, with next-day shipping available on domestic orders. Built-to-order items typically run 4 to 6 weeks.

Buy From the Page That Matches Your Truck

If you have the new truck, start at the 2027+ Ram TRX collection. If you have a 2021, 2022, 2023 or 2024, start at the 2021–2024 Ram TRX collection. Anything that appears on both pages fits both trucks.

And if the first thing you want is the thing most TRX owners buy first — a level stance that does not cost you a set of ball joints — start with the leveling collar, the rear plates and an alignment, and build from there. Nothing in that first order gets thrown away when you go further.

Not sure which parts your truck needs? Call and tell us the year, what is already on it and how you drive it. That conversation is free, and it saves more money than any discount code.

Leave a comment

Please note: comments must be approved before they are published.