2021-2026 Ford F-150 Raptor 5-Link Rear Axle Mount Kit - Upper, Lower, Panhard & Spring, Stock Position Weld-On
Description
Description
Every weld-on mount a Gen 3 five link rear axle needs, in one kit — upper link mounts, lower link mounts, panhard bar mount and spring mount plates, all cut to the stock Gen 3 positions.
This is the kit that turns a Gen 1 or Gen 2 Raptor axle housing into a Gen 3 five link axle. It is also the answer when a Gen 3 housing has taken enough damage that replacing several mounts makes more sense than replacing them one at a time.
All brackets laser cut from .250" mild steel and MIG welded. Shipped in raw steel.
What Is In The Kit
All four mount types, in stock position:
- Upper link mounts — for the two upper trailing arms
- Lower link mounts — for the two lower trailing arms, with limit strap tabs built in
- Panhard bar mount — factory position, retains stock panhard geometry
- Spring mount plates — coil springs in the stock location
Each is also sold separately if you only need one: upper, lower, panhard, spring.
Who Buys The Full Kit
Converting an older axle
A Gen 1 or Gen 2 Raptor axle housing has none of the Gen 3 five link pick-up points — the Gen 2 rear is leaf sprung entirely. This kit gives an existing housing the full set, in the right places, so it can run Gen 3 rear suspension.
Rebuilding a damaged housing
When a rear end has been hit hard enough to damage more than one mount, replacing the lot is often less work than chasing them individually — and cheaper than a new axle.
Custom builds
Raw steel, known geometry, all four mount types. The sensible foundation for a one-off rear end.
Construction & Fitment
- .250" (1/4") mild steel throughout, laser cut
- MIG welded assemblies
- Raw steel finish — no coating to burn off at the weld
- All mounts cut to stock Gen 3 positions
Built to the Gen 3 and Gen 3.5 Ford F-150 Raptor five link axle configuration, model years 2021 through 2026 including the Raptor R. Also the kit for adapting a Gen 1 or Gen 2 Raptor axle housing to that geometry.
Installation
Every bracket welds directly to the axle housing. Qualified fabricator only. Mount positions set the entire rear suspension geometry — there is no adjusting around brackets welded in the wrong place.
We do axle work in-house in Mesa, Arizona. Install guides are at Install Instructions.
Questions
Will this convert my Gen 2 axle to Gen 3 five link?
Yes — the axle side of it. You also need the frame side, which is the rear arm frame mount kit, plus the rear spring and panhard bar mount kit. The complete Gen 2 to Gen 3 conversion kit bundles the whole job.
Is this for long travel?
No — everything here is stock position. Long travel relocates the spring, shock and panhard mounts.
Does it come coated?
No, raw steel. You weld clean and finish it to match the rest of the axle.
Where is it made?
Laser cut, welded and finished in-house at our facility in Mesa, Arizona, USA.
The Frame Side Of The Job
- Rear arm frame mount kit — the link mounts on the frame
- Rear spring & panhard bar mount kit — the frame side spring and panhard mounts
- Stock location shock mount kit
- Complete Gen 2 to Gen 3 conversion kit — everything at once
The full catalog is on Gen 3 Raptor Rear Suspension.
Couldn't load pickup availability
Delivery and Shipping
Delivery and Shipping
- All in-stock products typically ship within 48 hours.
- For items that are not currently in stock, please expect 4–6 weeks for production and delivery.
- For stock status on products, contact our customer service team, and a representative will assist you with the most up-to-date availability and information: (480) 718-9800 | info@foutzmotorsports.com
PROP 65 WARNING
PROP 65 WARNING
This product can expose you to chemicals which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov


